乐彩网

  • <tr id='NyfqRR'><strong id='NyfqRR'></strong><small id='NyfqRR'></small><button id='NyfqRR'></button><li id='NyfqRR'><noscript id='NyfqRR'><big id='NyfqRR'></big><dt id='NyfqRR'></dt></noscript></li></tr><ol id='NyfqRR'><option id='NyfqRR'><table id='NyfqRR'><blockquote id='NyfqRR'><tbody id='NyfqRR'></tbody></blockquote></table></option></ol><u id='NyfqRR'></u><kbd id='NyfqRR'><kbd id='NyfqRR'></kbd></kbd>

    <code id='NyfqRR'><strong id='NyfqRR'></strong></code>

    <fieldset id='NyfqRR'></fieldset>
          <span id='NyfqRR'></span>

              <ins id='NyfqRR'></ins>
              <acronym id='NyfqRR'><em id='NyfqRR'></em><td id='NyfqRR'><div id='NyfqRR'></div></td></acronym><address id='NyfqRR'><big id='NyfqRR'><big id='NyfqRR'></big><legend id='NyfqRR'></legend></big></address>

              <i id='NyfqRR'><div id='NyfqRR'><ins id='NyfqRR'></ins></div></i>
              <i id='NyfqRR'></i>
            1. <dl id='NyfqRR'></dl>
              1. <blockquote id='NyfqRR'><q id='NyfqRR'><noscript id='NyfqRR'></noscript><dt id='NyfqRR'></dt></q></blockquote><noframes id='NyfqRR'><i id='NyfqRR'></i>
                语言选择: 中文版 line 英文版

                新闻中心

                做直流电源电杆拉线的ξ注意点

                      紧拉直流电源的电源线时,应把上把的末端穿入下ζ 把鼻子内,用紧线器夹伴上把,把它把的1-2股铁线穿在紧线器轴内,转动紧︽线器手柄,再把上把的股铁线穿在紧线器轴内「,然后转动紧线器手柄,把拉线逐渐▅拉紧,直到紧好为止,拉线〒紧好后,用另外的直径为3.2的镀锌』铁线从下向上绑扎,边绑扎边用木棒把绑线敲紧,下部绑扎150mm左右,花绑450mm左右,上部绑扎80mm左右。使用花篮螺丝时,应在紧拉线前把花∏篮螺丝拧到头,以便调整,紧完拉线后用镀锌◤铁线把花篮螺丝封死,防止因松动而造成倒杆事故。加装↓拉线绝缘子时,应使上下把交叉套在拉线绝缘子上,即使拉线绝缘子损坏了,也下把也不会脱离。

                栏目导航

                ?

                联系我们

                CONTACT US

                电话:0513-66686869

                邮箱:szh00111@163.com

                地址:江苏省启东市∑江海路888号

                用手机扫描二维码关闭
                二维码